Coax Cable Assemblies mobile mounts
Standard mobile lip mount cable assembly
Can be used with a lip mount or used alone as permanent hole mount. An o-ring is included to seal moisture from migrating under the threaded nut holding the connector in place, but additional water-proofing using silicone is recommended around the connector threads.13 feet of low loss coax, .25″ outside diameter
Gold-plated UHF (PL-259/SO-239) connectors
The PL-259 connector has a reverse threaded barrel. Turn the outer barrel clock-wise and it will thread off the connector body. The coax can then be routed through small holes or pushed through tight spaces without completely removing the connector. After routing the coax into place, screw the barrel back onto the PL-259 connector.
To shorten the over-all length of the coax:
Remove the barrel as above and de-solder the center pin of the PL-259
The connector body then screws apart and the cable can be cut to the desired length.
Re-assemble the connector.
Standard Cable Assembly with N-Connectors.
Can be used with a lip mount or used alone as permanent hole mount. An o-ring is included to seal moisture from migrating under the threaded nut holding the connector in place, but additional water-proofing using silicone is recommended around the connector threads.
13 feet low loss coax, .25″ diameter
Recommended for use to 1300MHz.
Gold-plated N-type connectors
The N-male connector has a reverse threaded barrel. Turn the outer barrel clock-wise and it will thread off the connector body. The coax can then be routed through small holes or pushed through tight spaces without completely removing the connector. After routing the coax into place, screw the barrel back onto the N connector.
To shorten the over-all length of the coax:
Remove the barrel as above and de-solder the center pin of the N connector
The connector body then screws apart and the cable can be cut to the desired length.
Re-assemble the connector.
Standard mobile lip mount cable assembly
Can be used with a lip mount or used alone as permanent hole mount. An o-ring is included to seal moisture from migrating under the threaded nut holding the connector in place, but additional water-proofing using silicone is recommended around the connector threads.13 feet of low loss coax, .25″ diameter
Gold-plated UHF (PL-259/SO-239) connectors
The PL-259 connector has a reverse threaded barrel. Turn the outer barrel clock-wise and it will thread off the connector body. The coax can then be routed through small holes or pushed through tight spaces without completely removing the connector. After routing the coax into place, screw the barrel back onto the PL-259 connector.
To shorten the over-all length of the coax:
Remove the barrel as above and de-solder the center pin of the PL-259
The connector body then screws apart and the cable can be cut to the desired length.
Re-assemble the connector.
Low loss mobile mount coax cable assembly
Approximate loss: 2dB at 2400MHz
13′ very low loss coax cable assy recommended for use up to 2500MHz
Coax cable outside diameter: 5/16″
Gold plated N-connectors
Can be used with a lip mount or used alone as permanent hole mount. An o-ring is included to seal moisture from migrating under the threaded nut holding the connector in place, but additional water-proofing using silicone is recommended around the connector threads.
The N-male connector has a reverse threaded barrel. Turn the outer barrel clock-wise and it will thread off the connector body. The coax can then be routed through small holes or pushed through tight spaces without completely removing the connector. After routing the coax into place, screw the barrel back onto the N connector.
To shorten the over-all length of the coax and avoid excessive cable loss-
Remove the barrel as above and de-solder the center pin of the N connector
The connector body then screws apart and the cable can be cut to the desired length.
Re-assemble the connector.
Deluxe mobile lip mount cable assembly
Coax length: 9′ 9″ total
The first 18″ of coax is mini RG-174A/U type allowing easy entry into the vehicle through the weather seal without causing wind noise, water leaks or impedance mismatch due to the coax being crimped or damaged.
The balance of the coax is low loss, .25inch outside diameter.
Gold-plated UHF (PL-259/SO-239) connectors
The PL-259 connector has a reverse threaded barrel. Turn the outer barrel clock-wise and it will thread off the connector body. The coax can then be routed through small holes or pushed through tight spaces without completely removing the connector. After routing the coax into place, screw the barrel back onto the PL-259 connector.
To shorten the over-all length of the coax:
Remove the barrel as above and de-solder the center pin of the PL-259
The connector body then screws apart and the cable can be cut to the desired length.
Re-assemble the connector.
Max Power:
HF: 100W
VHF: 75W
UHF: 50W
Deluxe mobile lip mount cable assembly
Coax length: 16′ 9″ totalThe first 18″ of coax is mini RG-174A/U type allowing easy entry into the vehicle through the weather seal without causing wind noise, water leaks or impedance mismatch due to the coax being crimped or damaged.
The balance of the coax is low loss, .25 inch outside diameter.
Gold-plated UHF (PL-259/SO-239) connectors
The PL-259 connector has a reverse threaded barrel. Turn the outer barrel clock-wise and it will thread off the connector body. The coax can then be routed through small holes or pushed through tight spaces without completely removing the connector. After routing the coax into place, screw the barrel back onto the PL-259 connector.
To shorten the over-all length of the coax:
Remove the barrel as above and de-solder the center pin of the PL-259
The connector body then screws apart and the cable can be cut to the desired length.
Re-assemble the connector.
Max Power:
HF: 100W
VHF: 75W
UHF: 50W
